Complete Set of CAMPUS® Data, ASTM Data, Biopolymer Database, Application Database, Tradename Database, Literature Database, Toolbox.

Material datasheets available free. Online registration at: www.materialdatacenter.com

Material Data Center is a leading international information system for the plastics industry. Material Data Center offers a comprehensive plastics database, calculation tools, CAE interfaces, a literature database and an application database. For more information about Material Data Center visit www.materialdatacenter.com.

This is the free Material Data Center Datasheet of BERGAMID® B700G10H - PA6-GF10 - Avient Corporation

Material Data Center offers the following functions for BERGAMID® B700G10H:
unit conversion, PDF datasheet print, comparison with other plastics, snap fit calculation, beam deflection calculation, CAE Interfaces

Check here, which other Bergamid B datasheets, application examples or technical articles are available in Material Data Center

Use the following short links to get directly to the properties of interest in this datasheet:
Proprietà Meccaniche - Proprietà Termiche - Proprietà Elettriche - Altre Proprietà - Proprietà Specifiche Materiale - Preparazione Provette
Any use of this information falls under the rules of our disclaimer.
Testo del prodotto
Resistant. Negligible, reversible or no changes in mass and dimensions.

Please consider the information about the application of the materials.
Proprietà Meccanichesecco/condUnitáNorma del test
ISO Data
Modulo a trazione 3000 / 5000 MPa ISO 527
Carico unitario a rottura 60 / 110 MPa ISO 527
Deformazione a rottura 7 / 3.5 % ISO 527
Resistenza all'urto Charpy, +23°C 90 / 50 kJ/m² ISO 179/1eU
Resistenza all'urto Charpy, -30°C - / 45 kJ/m² ISO 179/1eU
Resist. urto Charpy con intaglio, +23°C 18 / 7 kJ/m² ISO 179/1eA
Resist. urto Charpy con intaglio, -30°C - / 7 kJ/m² ISO 179/1eA
Proprietà Termichesecco/condUnitáNorma del test
ISO Data
Temperatura di fusione, 10°C/min 223 / * °C ISO 11357-1/-3
Temp.di inflessione sotto carico, 1.80 MPa 205 / * °C ISO 75-1/-2
Temp.di inflessione sotto carico, 0.45 MPa 220 / * °C ISO 75-1/-2
Reaz. al fuoco spess.nom. 1.5mm HB / * class IEC 60695-11-10
Spessore provato 1.5 / * mm -
Yellow Card disponibile sì / * - -
Reazione al fuoco a spessore h HB / * class IEC 60695-11-10
Spessore provato 0.7 / * mm -
Yellow Card disponibile sì / * - -
Proprietà Elettrichesecco/condUnitáNorma del test
ISO Data
Costante dielettrica relativa, 1MHz 7 / 3.7 - IEC 62631-2-1
Fattore di dissipazione, 1MHz 2200 / 250 E-4 IEC 62631-2-1
Resistività volumica 1E10 / 1E13 Ohm*m IEC 62631-3-1
Resistività superficiale * / 1E10 Ohm IEC 62631-3-2
Rigidità dielettrica 70 / 80 kV/mm IEC 60243-1
Res. Alle correnti striscianti superficiali 500 / - - IEC 60112
Altre Proprietàsecco/condUnitáNorma del test
Assorbimento d'acqua 8.6 / * % Sim. alla ISO 62
Assorbimento d'umidità 2.7 / * % Sim. alla ISO 62
Massa volumica - / 1190 kg/m³ ISO 1183
Proprietà Specifiche Materialesecco/condUnitáNorma del test
ISO Data
Numero di viscosità 150 / * cm³/g ISO 307, 1157, 1628
Preparazione ProvetteValoreUnitáNorma del test
ISO Data
Stamp. ad Iniezione, temp. di fusione 270 °C ISO 294
Stamp. ad Iniezione, temperatura dello stampo 80 °C ISO 294
Caratteristiche
Processabilità e Forma di Forni
Stampaggio ad Iniezione
Forma fisica disponibile
Pellet
Caratteristiche speciali
Stabilizzato o stabile al calore
Disponibilità geografica
Europa
Altre informazioni
Stampaggio ad Iniezione
Limited resistance. Considerable dimensional changes, and possibly
irreversible changes in properties after prolonged contact. Consultation
advisable before use.

Please consider the information about the application of the materials.
Disclaimer
Copyright Altair Engineering GmbH. Altair Engineering GmbH assumes no liability for the system to be free of errors. The user takes sole responsibility for the use of this data under the exclusion of every liability from Altair Engineering GmbH; this is especially valid for claims of compensation resulting from consequential damages. Altair explicitly points out that any decision about the application of materials must be double checked with the producer of this material. This includes all contents of this system. Copyright laws are applicable for the content of this system.
Created: Source: www.materialdatacenter.com


Material Data Center is provided by M-Base Engineering + Software GmbH. M-Base Engineering + Software GmbH assumes no liability for the system to be free of errors. Any decision about the application of materials must be double checked with the producer of this material.

Additional information about this material, like producer contact address, etc. can be found at www.materialdatacenter.com. For access to this extra information a registration is requested. Free online registration is available.